Davey 2PP65H Poly Pump

$1,494.60

This product is not available to buy online. If you wish to purchase any other product, for click and collect or delivery please call us on (03) 8795 7715 or CLICK HERE to send us your details.

    Davey 2PP65H Poly Chemical Engine Pump

    The Davey 2” Poly Pump is a robust, self-priming centrifugal pump manufactured from 30% glass filled polyester and is capable of pumping most agricultural
    chemicals. It is powered by a Honda GX200 engine and provides flows up to 600lpm and heads up to 40 metres. Pump comes with standard 2 year warranty.
    Dimensions (mm): 493L x 396W x 360H

     

    APPLICATIONS
    • Agricultural fertiliser and agchem transfer
    • High volume water transfer
    • Aquaculture

    OPERATING LIMITS

    Flow Capacities up to: 600 lpm
    Maximum total head: 40 m
    Maximum suction lift: 4.5 m
    Maximum water temperature: 50°C
    Minimum water temperature: 1°C
    Maximum casing pressure: 620 kPa
    Minimum suction pipe size: 2″
    Suction pipe strainer: Required
    Inlet size: 2″
    Outlet size: 2″

    ENGINE DATA
    Engine brand: Honda
    Engine model: GX200
    Engine type: Overhead valve
    Displacement: 196 cc
    Fuel tank: 3.6 litres
    Oil capacity: 0.6 litres
    Compression ratio: 8.5 : 1
    Air filter type: Dual stage – foam prefilter with paper element final filter
    Spark arrester: Yes
    Approximate fuel consumption: @ full load @ 3600rpm: 2.05 l/hr
    Noise: @ 4m @ full 3600 rpm @ full head: 86 dBa

    HANDLING
    This pump is light weight (22Kg dry weight) and comes with a carry handle for
    easy portability.

    INSTALLATION
    Pump Location

    • For the most efficient operation, site the pump as close to the water as practical.
      It is essential for the correct function of the engine that it be located on a
      horizontal surface. If allowed to run at an inclination, the oil lubrication system of
      the engine may not operate correctly. Subsequent engine failure would not be
      covered by the manufacturer’s guarantee.
    • The pumps should be positioned in a well-drained location to avoid possible
      property damage by leaking hose fittings or pump seals, spilled engine fuel, etc.
    • If you intend to operate your pump on a hard surface, Davey suggest a suitable
      resilient mounting to be fitted to your pump and engine.

    SUCTION PIPING
    A reinforced or non-collapsible hose should be used for the pump suction. The
    minimum suction pipe size should be 50mm (2”) I.D. A strainer should always be
    fitted to the bottom of the suction pipe. The strainer should be kept out of sand,
    mud, etc., to avoid particles being drawn into the pump and causing damage by
    abrasion.

    Always locate the pump so that the rise of suction pipe from the water is even with
    no humps or hollows where air may be trapped.
    All pipe connections must be air tight to ensure the best priming and operation of
    the pump. Check that the washers in nuts and tails are in good order.
    Discharge Piping
    Care should be taken on correct selection of discharge pipe pressure rating as the 2”
    Poly Pump is capable of delivering pressures up to 280kPa (41psi). The pump outlet
    is 2” BSP female and 2”, or larger, polythene piping or equivalent should be used.

    PUMP OPERATION

    Priming the Pump

    • Do not attempt to run pump if the pump casing (pump body) has not been filled with water (primed). Severe damage will result to
      mechanical seal.
    • To prime the pump initially, it is necessary to fill the pump body with
      water before starting the engine. Remove the priming cap (on top of
      the pump casing near the discharge port). Fill the pump body with
      water and refit the priming cap tightly.

    STARTING THE PUMP
    Choke and start the engine, open the discharge valve and then allow the pump to
    run until it is drawing water. The pump will establish prime better at higher engine
    speeds. Allow up to 3 minutes for long or deep suctions lifts.

    High performance can be obtained from these pump if the engine speed is
    increased, however, we do not recommend the pump be operated over 3,600rpm
    for extended periods as this may overload the engine. Operating the engine
    at full throttle for extended periods will shorten the engine’s life and may result
    in premature failure. For operations such as irrigation or dam and tank filling,
    the throttle should be closed to around ¾ maximum. This should correspond to
    around 3,000rpm maximum.

    PUMPING OTHER THAN CLEAN WATER
    When pumping other than clean water, the specific gravity or relative weight of
    the fluid may be different to water. If the fluid being pumped is heavier than water,
    such as pumping liquid fertilizers, then the load on the pump will be increased. In
    these cases care should be taken to ensure the engine is operated at lower flows
    to relieve the load. This can be achieved by partially closing an outlet valve.
    AVOIDING PUMP DAMAGE

    • Pumping water containing sand, dirt or other abrasive materials will result in
      accelerated pump wear and mechanical seal failure. Damage of this kind is not
      covered by the guarantee.
    • Never operate the pump against closed head or with no discharge flow as this
      will lead to damage to the pump not covered by the guarantee. If the pump is
      required to operate at no flow then a bypass line should be used to return flow to
      the source or to waste.
    • This pump is not designed to boost high incoming pressure and should not be
      connected to mains or other pressuring water supplies as this may result in
      discharge pressures above the rated casing pressure capacity. Damage to the
      pump from such over pressurisation is not covered by the guarantee.

    STORAGE OF PUMP
    The pump should be drained of water or chemicals and normal engine storage
    procedure should be followed. Run the pump until the fuel is exhausted; drain
    the fill the sump with fresh oil. The pump should be stored in a dry place. Before
    starting the pump after storage it should be checked to make sure that it is free to
    rotate by pulling the starter rope with the ignition off.

    Brand

    Davey Water Products

    Davey offers a range of water related services from water transfer, conservation, treatment and filtration; to help ensure your products are built to last. You can Depend on Davey, every time. Water is our world. For 85 years so far, Davey has been manufacturing products that help protect and enhance people’s lives. Whether you need perfect pressure, healthy drinking water, protection from fire and flood, a clean, relaxing pool or spa, or water to run your farm or business, you can depend on Davey for the right solution.
    davey logo
    Wishlist 0
    Continue Shopping